This is the Futaba 6JA 6-Channel 2.4GHz
S-FHSS and FHSS Selectable Mode Radio System
with the R2006GS Receiver and four S3004 Servos.
The 6J transmitter is "full range".
Only available in .
This is the airplane version with the ratcheted throttle stick.
(See COMMENTS for optional battery and charger choices)
Selectable S-FHSS and FHSS modes, the included R2006GS receiver
automatically adapts to the selected mode
Capable of 4 channels only in FHSS mode
Fail safe on all channels in S-FHSS mode only (throttle channel only
when FHSS mode is selected)
15 model memory with 4 character model naming
40x40 127 segment LCD display
Modes 1-4 selectable by pilot
R2006GS high-voltage (4.8 - 7.4V) 6-channel receiver with Easy-Link
circuitry, frequency hopping, spread spectrum design and Dual
Antenna Diversity
Endpoint adjustment (EPA), sub trims, servo reversing & throttle cut
Throttle position, mix and low battery warnings
Trainer system (trainer cord not included)
One year limited warranty through Hobby Services beginning at date of
purchase
Airplane Features;
Two programmable mixes and two 5-point throttle curves
Two 5-point pitch curves
Flaperon with differential rate
Flap trim (2 rates)
V-tail mixing
Elevon mixing
Helicopter Features;
Two 5-point throttle curves
Three 5-point pitch curves
Throttle hold
Hover pitch
Gyro and revo mixing
Four swash plate types (H1, H3, HR3 & H3 w/AFR)
Swash AFR (ail/ele/pitch)
Throttle mix
Electronic swash ring
Throttle and pitch delay
Futaba 6J 6-Channel Transmitter, R2006GS Receiver and Instruction
Manual, Neckstrap, Servo Tray and Mounting Hardware, On/Off Switch
and ratchet spring
Four S3004 Standard Ball Bearing Servos, FUTM0004
AA Cells: Four for transmitter
Transmitter;
Type: 2-stick, 6-channel, FHSS/S-FHSS selectable
Frame Rate: 6.8ms
Current Drain: 170mA
Receiver;
Modes: FHSS or S-FHSS (auto selectable)
Power Requirements: 4.8V-7.4V
Compatible Batteries: NiCd, NiMH, LiPo, LiIon & LiFe
Dimensions: 1-11/16 x 15/16 x 5/16" (43 x 24 x 7.9mm)
Weight: 0.29oz (8.3g)
Current Drain: 80mA (@ no signal)
S3004 Servo;
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6.0V
Torque: 44 oz-in (3.2 kg-cm) at 4.8V
57 oz-in (4.1 kg-cm) at 6.0V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
(40 x 20 x 36mm)
Weight: 1.3 ounce (1-5/16oz) (37 grams)
Connector: "J" type with approx. 5" wire
To use the NiMH battery FUTM1482, you will need to purchase
charger FUTM1832. Then call Futaba Services
and they will send you a battery door- HSP82469. If
you already have a charger and need a charge lead they can
sell you part number- HSP29615. (requires soldering on the
correct charger plugs)
You may also use a 2C 6.6V LiFe battery such as HCAM6521
jxs 02/28/11
ir/jxs
updt jxs 12/05/11
updt jpg 2/25/13
JMLM 11/28/14
|