Tekno RC 1/8 ET48.3 Competition Truggy 4WD Kit

Tower Stock# LXFPDP  •  Manufacturer Stock# TKR5602
  • Thumbnail 1 (see larger view)
  • Thumbnail 4 (see larger view)
Shipping Restricted ItemDetails
Easy Pay
Request 2 Payments ($300.00, $299.99) Details
Notes from our tech department:
This is the Electric Powered, Radio Controlled, 18 Scale
4WD Competition ET48.3 Truggy Kit from Tekno RC.

New trailing front spindles and spindle carriers
New V2 hinge pin braces and inserts
New clamping spring perches with captured shock boots
New rear hubs
Low profile wing mount
Revised bumper for increased ground clearance
New split center differential mount
New straight turnbuckle rod ends
New tapered aluminum front center driveshaft
New easily adjustable droop screws
Revised shock standoffs for easier droop measurement
Updated setup sheet for improved handling


Chassis: CNC machined hard anodized aluminum 0.16 (4mm) thick
optimized narrow layout, adjustable brace system for fine tuning
chassis flex with front, center, and rear braces
Drive: Four wheel CV driveshafts with captured pins on all four
Differentials: Three fluid filled, with straight cut CNC machined
hardened steel ring and pinion gears,
Motor Mount: Two-piece CNC machined, dual clamping gear mesh
adjustment, lightweight direct-to-diff mount design, mount
accomodates truggy or long can motors up to 78mm long, mount uses
standard MOD 1 pinion, Tekno RC Traktion Drive or Elektri-Clutch
Shocks: CNC machined hard anodized aluminum bodies, 16mm bore, 4mm
hardened steel polished shafts, 5.4 (137mm) long rear shocks,
4.8 (122mm) long front shocks, truggy specific springs, CNC
machined 8x1.3mm tapered pistons
Shock Towers: CNC machined anodized 7075 aluminum, front 0.24 (6mm)
thick, rear 0.20 (5mm) thick, revised shock standoffs for easier
droop measurement
Suspension: Fully adjustable long travel geometry, truggy specific
arms and sway bars, lightened aluminum pivot balls, adjustable
anti-squat, rear arms, roll center, and bump steer
Body: Clear truggy type with high downforce wing, & low center of
gravity lightweight wing mount
Steering: Full ball bearing equipped, lightened aluminum posts,
adjustable bump steer and Ackerman, Ackerman describes the effect
of the inside front wheel turning faster than the outside front
wheel during turns, adjustable stops, CNC machined aluminum
Ackerman plate, adjustable steering stops for precise steering
travel settings
Caster: Adjustable, castertoe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to
the chassis
Camber: Adjustable front and rear, camber refers to the angle of the
tops of the tires from vertical when viewed from front or behind


ET48.3 Truggy Kit with Body, Decals, Shocks, Shock Oil, Diff Oil, and


Radio: 2-3 channel with high-torque steering servo, and optional
brake servo
Motor: Brushless recommended
ESC: Compatible with selected motor
Battery: 4-6S LiPo
Battery Charger: For selected battery
MOD 1 Pinion or Traktion DriveElektri-Clutch system
Tires and Wheels: 18 scale truggy type with inserts
Paint, building and track equipment


Length: 23.4 (595mm)
Wheelbase: 14.8-15.1(375-385mm) adjustable
Weight: 9lbs (4000g) varies with equipment & battery used
Width: 16.4-16.5* (416-420mm*) *optional hubs required
Dry Weight: 9.0lbs (4000g) may vary with equipment used
Diff Ratio: FR 940t, center 44T
Battery Tray Dimensions: 1.9x5.8 (50x148mm) 2x2s or 1x4s config.
Length: 17.5 (444mm)
Width: 4.8 (123mm)
Height: 5 (127mm)


For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 8x16mm Center Diff 1 DTXC1585
2 8x16mm Front Diff 1 DTXC1585
2 8x16mm Rear Diff 1 DTXC1585
2 5x11mm Front Gearbox 1 DTXC1547
2 5x13mm Rear Gearbox 1 TKRC5015
2 13x19mm Rear Hubs 1 TKRC3194
2 8x16mm Rear Hubs 1 DTXC1585
2 13x19mm Front Hubs 1 TKRC3194
2 13x19mm Front Hubs 1 TKRC3194
4 6x10mm Steering 2 DTXC1561

jxs 081115



Product Documents & Files

Manufacturer Contact Information