Tekno RC 1/8 NT48.3 Competition Nitro Truggy 4WD Kit

Tower Stock# LXFSJT  •  Manufacturer Stock# TKR5406
  • Thumbnail 1 (see larger view)
  • Thumbnail 4 (see larger view)
Easy Pay
Request 2 Payments ($325.00, $324.99) Details
Notes from our tech department:
This is the Glow Powered, Radio Controlled, 1/8 Scale
4WD Competition NT48.3 Truggy Kit from Tekno RC.

NT48.3 New Features Include;
Revised Chassis
New Clamping Spring Perches with Captured Shock Boots
New Rear Hubs
New Trailing Front Spindles and Spindle Carriers
New V2 Hinge Pin Braces and Inserts
Revised Bumper for Increased Ground Clearance
New Straight Turnbuckle Rod Ends
Easily Adjustable Droop Screws
New Brake Linkage for Easier Adjustments and More Consistent Braking
Revised 46T Spur Gear
New Brake Pads and Discs
Updated Setup Sheet for Improved Handling

FEATURES

Chassis: CNC machined hard anodized aluminum 0.16" (4mm) thick
lightened chassis
Drive: Four wheel CV driveshafts with captured pins on all four
wheels
Differentials: Three fluid filled, with straight cut CNC machined
hardened steel ring and pinion gears, offset rear diff provides
minimum drive angles and reduced wear
Engine Mount: Engine can be mounted in forward or rearward position
(18mm) offset
Shocks: CNC machined hard anodized aluminum bodies, 16mm bore, 4mm
hardened steel polished shafts, 5.4" (137mm) long rear shocks,
4.8" (122mm) long front shocks, truggy specific springs, CNC
machined 8x1.3mm tapered pistons
Shock Towers: CNC machined anodized 7075 aluminum, front 0.24" (6mm)
thick, rear 0.20" (5mm) thick
Suspension: Fully adjustable long travel geometry, truggy specific
arms and sway bars, lightened aluminum pivot balls, adjustable
anti-squat, rear arms, roll center, and bump steer
Brakes: Larger, fully CNC machined, hardened, and ground discs,
improved semi-metallic brake pads are now separated by springs
system redesigned for better consistency and easier bias
adjustments
Clutch: Four 7075 aluminum shoes
Fuel Tank: 5.1oz (150cc)
Body: Clear truggy type with high downforce wing, & adjustable low
profile wing mount
Front Bumper: Revised to increase ground clearance
Throttle Linkage: CNC machined assembly riding on ball bearings
Hubs: New rear hub design allows use of stock CV axles, or
universal driveshafts
Steering: New trailing steering spindles and carriers, full ball
bearing equipped, lightened aluminum posts, adjustable bump steer
and Ackerman, Ackerman describes the effect of the inside front
wheel turning faster than the outside front wheel during turns,
adjustable stops
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to
the chassis
Camber: Adjustable front and rear, camber refers to the angle of the
tops of the tires from vertical when viewed from front or behind
vehicle

INCLUDES

NT48.3 Truggy Kit with Body, Decals, Shocks, Shock Oil, Diff Oil,
and Instruction Manual

REQUIREMENTS

Radio: 2-3 channel with high-torque steering servo
Engine: .21-.28 cu in truggy type
Receiver Battery: 6V, hump comfiguration
Tires and Wheels: 1/8 scale truggy type with inserts
Starter box and glow igniter
Fuel and fuel bottle
Paint, building and track equipment

SPECIFICATIONS

Vehicle-
Length: 23.4" (595mm)
Wheelbase: 14.8-15.1"(375-385mm) adjustable
Width: 16.4-16.5" (416-420mm)
Dry Weight: 8.8bs (4000g) may vary with equipment used
Diff Ratio: F/R 9/40t, center 46T
Body-
Length: 17" (432mm)
Width: 7.25" (184mm)
Height: 4.1" (105mm)

COMMENTS

For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 8x16mm Front Diff 1 DTXC1585
2 8x16mm Center Diff 1 DTXC1585
2 8x16mm Rear Diff 1 DTXC1585
2 5x11mm Front Gearbox 1 DTXC1547
2 5x11mm Rear Gearbox 1 DTXC1547
4 8x16mm Rear Hubs 2 DTXC1585
2 13x19mm Front Hubs 1 TKRC3194
2 8x14mm Front Hubs 1 DTXC1583
4 6x10mm Steering 2 DTXC1561
1 5x13mm Clutch 1 TKRC5134
1 5x10mm Clutch 1 DTXC1547

jxs 09/21/15

Resources

References

Product Documents & Files

Manufacturer Contact Information