Kyosho 1/8 Inferno GT2 Challenger Demon Nitro 4WD RTR

Tower Stock# KYOC3008  •  Manufacturer Stock# 33008B
  • Thumbnail 1 (see larger view)
  • Thumbnail 3 (see larger view)
  • Thumbnail 5 (see larger view)
  • Thumbnail 6 (see larger view)
Easy Pay
Request 3 Payments ($200.01, $199.99, $199.99) Details
Notes from our tech department:
This is the Glow Powered, 2.4GHz Radio Controlled, Ready to Run,
1/8 scale 2018 Spec Inferno GT2 Dodge Challenger SRT DEMON
Race Spec On-Road Car.

FEATURES

Chassis: Aluminum, with resin chassis stiffener, front center
gravity type radio box for improved stability
Drive: Four wheel shaft drive
Transmission: Two-speed
Differentials: Spiral type ring & pinion gear
Radio: Kyosho Syncro KT-331P FHSS transmitter with jog dials, 15
mode memory, endpoint adjustment, dual-rate and exponential
settings, KR331 receiver
Steering Servo: High torque KS5031-09MW metal-geared servo
Engine: Kyosho KE25 with pull starter, slide valve carburetor, rear
exhaust
Exhaust System: Polished aluminum tuned pipe
Clutch: 3-piece, 1.3" (34mm) small flywheel for sharp throttle
response
Wheels: Five spoke, black in color
Tires: On road 3.8 x 1.6" (97 x 40mm) with foam inserts
Brake: Front and rear independent disc
Fuel Tank: 5.1oz (150cc)
Front Bumper: Foam
Shocks: Oil-filled
Shock Towers: Composite plastic, 0.197" (5mm) thick
Ball Bearings: Full set, 18 on drive train and 2 on clutch bell
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle

INCLUDES

Assembled Dodge Challenger SRT DEMON, w/trimmed & painted Body, KE25
Engine, Tuned Pipe, Radio System, Wrenches and Instruction Manual

REQUIREMENTS

AA Batteries: Eight, four for transmitter, four for receiver
Fuel: Car blend with 15-30% nitro content, 20% required for break-in
Glow starter, track and maintenance equipment

SPECIFICATIONS

Vehicle;
Length: 20.3" (515mm)
Width: 12.2" (310mm)
Height: 5.3" (135mm)
Wheelbase: 14.2" (360mm)
Front Tread: 10.3" (262mm)
Rear Tread: 10.4" (265mm) distance from center of tires side-to-side
Ground Clearance: 0.59" (15mm)
Gear Ratio: 1st 10.14:1, 2nd 7.90:1
Weight: 8.04lbs (3650g)
Body;
Length: 25.4" (646mm)
Width: 11.6" (294mm) measured at center between wheel wells
Height: 6.2" (157mm)
Carburetor Settings;
Carburetor is preset from factory. Do not change default settings.
After break-in is complete and model is running normally
carburetor can be fine-tuned to suit temperature and humidity
conditions.
To adjust idle speed turn throttle stop screw in slightly to
increase idle speed, out slightly to decrease idle speed.
To adjust acceleration, close needle valve slightly to increase
acceleration, open slightly to decrease acceleration and to
richen fuel/air mixture.

COMMENTS

For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
4 8x16x5mm Fr Uprights 2 DTXC1585
4 8x16x5mm Rear Uprights 2 DTXC1585
2 8x16x5mm Fr Diff Bevel Gear 1 DTXC1585
2 8x16x5mm R Diff Bevel Gear 1 DTXC1585
2 5x10x4mm Clutch Bell 1 DTXC1535
2 8x16x5mm 2-sp Transmission 1 DTXC1585
2 6x10x3mm 2-sp Transmission 1 DTXC1561

jxs 02/26/18
ir/jxs

Resources

References

Product Documents & Files

Manufacturer Contact Information